[[samsung_p35]]
 
Zuletzt angesehen: • iptables • lighttpd • dotfiles • procmail • openldap • subversion • suse_linux • allgemeine • nuetzliches • samsung_p35
Inhaltsverzeichnis

Debian Sarge auf dem Samsung P35

1. NetInstaller besorgen

http://www.debian.org

http://www.debian.de/distrib/netinst

http://cdimage.debian.org/debian-cd/3.1_r0a/i386/iso-cd/debian-31r0a-i386-netinst.iso

2. Mit der NetInstaller CD das Samsung P35 booten

Eine normale Installation durchführen :-)

Bootoptionen 

expert26 bootkbd=de acpi=off

3. Konfigurieren

Ausgabe von lspci nach einem Update der Datenbank von lspci mittels 

update-pciids

ergibt folgende verbaute Hardware 

$ lspci -vv
0000:00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 21)
        Subsystem: Samsung Electronics Co Ltd: Unknown device c00c
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 0
        Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
        Capabilities: [e4] #09 [4104]
        Capabilities: [a0] AGP version 2.0
                Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
                Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x4
 
0000:00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 21) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 96
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
        I/O behind bridge: 00003000-00003fff
        Memory behind bridge: d0100000-d01fffff
        Prefetchable memory behind bridge: d8000000-dfffffff
        BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
 
0000:00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
        Subsystem: Samsung Electronics Co Ltd: Unknown device c00c
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 11
        Region 4: I/O ports at 1800 [size=32]
 
0000:00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
        Subsystem: Samsung Electronics Co Ltd: Unknown device c00c
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 5
        Region 4: I/O ports at 1820 [size=32]
 
0000:00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])
        Subsystem: Samsung Electronics Co Ltd: Unknown device c00c
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin C routed to IRQ 11
        Region 4: I/O ports at 1840 [size=32]
0000:00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI])
        Subsystem: Samsung Electronics Co Ltd: Unknown device c00c
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin D routed to IRQ 5
        Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] #0a [2080]
 
0000:00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
        Latency: 0
        Bus: primary=00, secondary=02, subordinate=04, sec-latency=64
        I/O behind bridge: 00004000-00004fff
        Memory behind bridge: d0200000-d02fffff
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
 
0000:00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 03)
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
 
0000:00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
        Subsystem: Samsung Electronics Co Ltd: Unknown device c00c
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 11
        Region 0: I/O ports at <unassigned>
        Region 1: I/O ports at <unassigned>
        Region 2: I/O ports at <unassigned>
        Region 3: I/O ports at <unassigned>
        Region 4: I/O ports at 1860 [size=16]
        Region 5: Memory at 40000000 (32-bit, non-prefetchable) [size=1K]
 
0000:00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
        Subsystem: Samsung Electronics Co Ltd: Unknown device c00c
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 5
        Region 0: I/O ports at 1c00 [size=256]
        Region 1: I/O ports at 1880 [size=64]
        Region 2: Memory at d0000c00 (32-bit, non-prefetchable) [size=512]
        Region 3: Memory at d0000800 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 
0000:00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 03) (prog-if 00 [Generic])
        Subsystem: Samsung Electronics Co Ltd: Unknown device c00c
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 5
        Region 0: I/O ports at 2400 [size=256]
        Region 1: I/O ports at 2000 [size=128]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 
0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10] (prog-if 00 [VGA])
        Subsystem: Samsung Electronics Co Ltd: Unknown device c00c
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B+
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
        Region 1: I/O ports at 3000 [size=256]
        Region 2: Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
        Capabilities: [58] AGP version 2.0
                Status: RQ=80 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
                Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 
0000:02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
        Subsystem: Samsung Electronics Co Ltd: Unknown device c00c
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (8000ns min, 16000ns max)
        Interrupt: pin A routed to IRQ 5
        Region 0: I/O ports at 4000 [size=256]
        Region 1: Memory at d0201800 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 
0000:02:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ac)
        Subsystem: Samsung Electronics Co Ltd: Unknown device c00c
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 168
        Interrupt: pin A routed to IRQ 5
        Region 0: Memory at 40001000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
        Memory window 0: 40400000-407ff000 (prefetchable)
        Memory window 1: 40800000-40bff000
        I/O window 0: 00004400-000044ff
        I/O window 1: 00004800-000048ff
        BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
        16-bit legacy interface ports at 0001
 
0000:02:01.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ac)
        Subsystem: Samsung Electronics Co Ltd: Unknown device c00c
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 168
        Interrupt: pin B routed to IRQ 11
        Region 0: Memory at 40002000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
        Memory window 0: 40c00000-40fff000 (prefetchable)
        Memory window 1: 41000000-413ff000
        I/O window 0: 00004c00-00004cff
        I/O window 1: 00005000-000050ff
        BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
        16-bit legacy interface ports at 0001
 
0000:02:01.2 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 04) (prog-if 10 [OHCI])
        Subsystem: Samsung Electronics Co Ltd: Unknown device c00c
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (500ns min, 1000ns max)
        Interrupt: pin C routed to IRQ 11
        Region 0: Memory at d0201000 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME+
 
0000:02:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev 05)
        Subsystem: Intel Corporation: Unknown device 2731
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (750ns min, 6000ns max), Cache Line Size: 0x08 (32 bytes)
        Interrupt: pin A routed to IRQ 5
        Region 0: Memory at d0200000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-

Framebuffer der Standardinstallation anpassen

Um die größtmögliche Auflösung des Samsung P35 von 1400×1050 zu erhalten muss der Code 0x342 dem Bootloader übergeben werden. Da ich mich bei der Installation für den Bootloader grub entschieden habe, werden ich die vorgehensweise an diesem exemplarisch darstellen.

Wir bearbeiten dazu die Datei /boot/grub/menu.lst und fügen der Zeile 

# kopt=root=/dev/hda4 ro noapic bootkbd=de acpi=off

Achtung: Diese Zeile kann von meiner Abweichen - dies ist nur ein Bsp!

den Zusatz vga=0x342 zu.

Die Zeile sieht somit folgendermaßen aus: 

# kopt=root=/dev/hda4 ro noapic bootkbd=de acpi=off vga=0x342

Damit die Konfiguration gültig wird, muss noch der folgende Befehl ausgeführt werden: 

update-grub

Anschließend kann der Rechner neu gestarten werden.

Eigener Kernel

Benötigte Pakete installieren: 

$ su -
apt-get install kernel-package libdb3-dev libncurses-dev
samsung_p35.txt · Zuletzt geändert: 2011/07/22 23:26 (Externe Bearbeitung)
 
Falls nicht anders bezeichnet, ist der Inhalt dieses Wikis unter der folgenden Lizenz veröffentlicht: CC Attribution-Noncommercial-Share Alike 3.0 Unported
Recent changes RSS feed Donate Powered by PHP Valid XHTML 1.0 Valid CSS Driven by DokuWiki